The 6 Best clamps On Amp Probe (2023 reviews)

If you are looking to buy an all-around great clamp for your daily purpose, etekcity clamp on amp probe is the right option. It is great for checking locked rotor amperage on a hvac compressor. It can test the diode only to test the current between the two ends. It comes with a handy bag, leaving some extra room for small parts. The select dial is smooth and locks crisply at each level. It includes a wrist strap attachment at the bottom. It will let you know if it's open, short or charged. The features it has can easily command many times more. It is great for testing outlets in the home.

Why We Like This:

Great inexpensive tool for the homeowner
Great little unit, good for quickly checking voltages and currents
Easy to use and easily fits the wires in the breaker panel

Best With Clamp Meter: Hantek Clamp On Amp Probe

Buy on Amazon

The hantek clamp on amp probe is capable of outshining several other clamp featured in this list in overall features for the price point. This tool is meant to be used in an electronics development environment. It is very useful for parasitic drain problems in the milliamp range. It does a remarkable job given its economical cost. It will work with any scope or graphing meter with a bnc connector.

This unit comes with a BNC connector, there are cables that adapt BNC to bananas. It takes 9V batteries so keep an extra handy. This is really useful for troubleshooting battery current draws on a vehicle that is off.

Why We Like This:

Steady state input is very measurable
New and hot release

Best With High end DMM: PDI Clamp On Amp Probe

Buy on Amazon

Not everyone likes to purchase clamp for their daily purpose, but the pdi clamp on amp probe would be an anomoly. The 60 handheld 60 amp ac/dc current clamp probe allows you to measure ac and dc current without disconnecting the existing wiring. It clamps around a wire and it outputs a voltage in response. The jaw opening is small and will not fit over most battery cables. It looks and feels well built. It is a great current probe for data loggers.

It is a sensitive current meter, must be used with a vom. It is the "zero calibration" feature. It works on all meters and Lab Scopes with banana plugs, which the Fluke 88 uses.

Why We Like This:

Well made and highly useful for automotive computer controlled diagnostics
Has cords long enough to actually use
Works good with meter for quick testing
Especially useful for larger currents (> 10 amp) which typical multimeter does not handle

Best With Temperature: Hantek Amp Probe

Buy on Amazon

We know from years of feedback from readers, customers and amazon sellers, what most people want in a convenient and appropriate clamp. The hantek amp probe is exactly that - it's a simple clamp that hits all the right notes. The 650 AC DC current clamp has a bnc cable end to be used with an oscilloscope. It is composed by permalloy and hall element, which linearly transform the ac or dc current to ac or dc current voltage. It allows to check ignition secondary on older vehicles (not coil-on-plug) and current draw while cranking. The current clamp range is set to 1mv/100ma, the actual current value is one hundred times of the measured data whose unit is mamma. The probe responds in high frequencies also, so good to mesure fast amperage.

The oscilloscope current pattern is adequate. It's max range is 650 amps.

Why We Like This:

Good accessory to allow full use of your scope
Power circuit measurement and malfunction analysis
Good brand reputation

Best For The money: ALLSUN Clamp On Amp Probe

Buy on Amazon

This product has a simple push-button auto-zero that can be operated with the thumb of the same hand holding the clamp. It permits the display to be placed a few feet away from the clamp, which makes it easier to get a clear view. It's compact, has a good metal insert for the battery door and good terminals for the battery.

This probe allows measurements of live circuit current without having to disconnect, simply put the clamp around one of the wires. It's a nice shade of blue, does not look like a toy, and feels good in the hand. The clamp size is large enough for most residential wiring and small enough to use in automotive (DC) environments where space is restricted. This is a very good amp clamp for the money, and easy to use.

Why We Like This:

Nice meter, zeros out very well and is accurate
Noisy, but works well for relative testing
Needs a 9v battery, no auto shutoff

Best For capacitor: Waporich Clamp On Amp Probe

Buy on Amazon

If you often find yourself confused about convenient and suitable clamp, waporich clamp on amp probe should be your first option for buying. It has a design for the higer ac/dc current test range. The max jaw size of 1.7 inches can measure up to 600 A DC/ AC current without interruption of the circuit. It is able to up to 600a, which is the best partner for digital multimeters. It is perfect for bench testing.

Why We Like This:

Has high resolution and is accurate, works great so far
A clamp adapter with test probes
Lot of satisfied buyers