The 8 Best Nodemcu Shields (2022 reviews)

If you often find yourself confused about a good shield, Hiletgo Nodemcu Shield should be your first option for buying. The hiletgo nodemcu shield is super cheap and has a functional design. The Manufacturer says: We provide a 100% satisfication service for customers. In addition, it is suitable for jumper wires, is many more, it is good enough and has a good design.

The shield comes with great stuff, can interfere with data rate, it is much more and has an amazing design. Above all, the hiletgo nodemcu shield is a highly integrated chip designed for the needs of a new connected world.

Almost all customers quickly discovered that the shield came with header pins soldered in place as pictured. And, a few also found that the shield works with konnected firmware. Also, they strongly agree that the quality of the module is clean and it works well.

Customers also found that its wise to buy a nodemcu expansion board and nodemcu development board, along with this shield.

Top Customer Quotes:

This is because there is a resistor network already in place to divide the voltage.
This is an excellent board for iot, remote control, etc.
This takes sometimes up to 1 minute.
It is easier to whip out the arduino ide and solve the problem that way.

Best For Lots Of Residual Flux: Makerfocus Nodemcu Shield

Buy on Amazon

Next on the list, we've got yet another shield that manages to win our hearts. It's the Makerfocus Nodemcu Shield and it's widely considered as one of the most convenient shields you can buy. The makerfocus nodemcu shield is portable, it goes to file and has a great design. Go to tools > board > board manager> type "esp8266" and download the community esp8266 and install. The entire solution, including the front - end module, is designed to occupy a minimal pcb area.

The shield is very good, is rapid, it is multifunctional and has a low power design. Finally, the makerfocus nodemcu shield works great, It is very helpful and has a solid design.

Most customers found that the shield is a great module for use with the arduino ide. And, a few say that the shield features packed into this tiny board. Also, they strongly agree that these boards apparently can only handle 10v input according to the back side of the breakout board, not the more standard 20v you'll find as the max online for nodemcu boards.

Few customers got nodemcu expansion board and nodemcu starter kit, along with the shield.

Top Customer Quotes:

These are well packaged for optimum protection.
This is under the tools menu in the arduino environment.
There is a way to guide you to use the new version.
This is available for most major OS'S.

Best For Hobbyists: Aideepen Nodemcu Shield

Buy on Amazon

Compared with other shields in this category, the Aideepen Nodemcu Shield has a convenient design. The aideepen nodemcu shield can connect a large number of digital lines to an arduino while maintaining the footprint of the original nano. You can use this adapter to easily hook up the arduino nano to the outside world via hooked up wires, and it can be used in conjunction with or in place of a breadboard. This makes using the nano much easier.

The shield is a terminal expansion adapter, works very well for prototyping arduino nano projects. Moreover, the shield will lead out all the nano pins. Most importantly, the aideepen nodemcu shield is a small and simple arduino nano expansion board.

Almost all buyers opine that the shield makes using the nano much easier. Further, a few say that the shield is a perfect way to test projects without soldering into arduino nano. Moreover, a few strongly agree that the shield fits off-brand nano copy and can be used afterwards as well. In conclusion, the tone of buyers is very positive and we believe that the shield suits the purpose.

Customers say that buying a nodemcu expansion board, with this shield made their life much easier.

Top Customer Quotes:

This is middle, worked fine and it is professional.
This is used to throw railroad switches on t-trak modules.
Great for temporary things you don't want to solder.
This is perfect for hobbyists or prototyping.

Best With Switch: Daoki Nodemcu Shield

Buy on Amazon

The Daoki Nodemcu Shield might be a relatively new release, but it's still nothing short of impressive this year, thanks to multiple price cuts and added new features over the past few months. The daoki nodemcu shield comes with a power switch, It allows for maximum power and has a great design. Make sure this fits by entering your model number. The use of short modules that can simultaneously control the board and motor.

The shield is made for the power button and has a humanized design. Most importantly, the daoki nodemcu shield is a compatible esp12e dev kit and for nodemcu a large current motor driver module.

Customers also discovered that its wise to buy a nodemcu expansion board and ph sensors for nodemcu, along with this shield.

Why We Like This:

This allows for maximum power dissipation and has a hardware design.
12e module, please note the direction consistent with an expansion board antenna.
This is reasonable, smd encapsulation, installation is very convenient.
The module adopts a folded plug-in circuit board design, can be directly accessed through the esp12e dev kit.

Best For Low Cost: Songhe Nodemcu Shield

Buy on Amazon

Not everyone likes to purchase a shield for their daily usage, but the Songhe Nodemcu Shield would be an anomoly. The songhe nodemcushield is a highly integrated chip designed for the needs of a new connected world. 12 based serial wifi integrated on board to provide GPIO, pwm, adc, i2c and 1-wire resources at your finger tips, built-in USB-TTL serial with super reliable industrial strength ch340 for superior stability on all supported platforms. The entire solution, including the front - end module, is designed to occupy a minimal pcb area.

Lastly, the songhe nodemcu shield is built based on the mature esp8266 technology to take advantage of the abundant resources available on the web.

Almost all customers agree that the shield does work and the added bonus is more room to prototype with. Further, they also found that this board is wider (28mm) than some nodemcu boards. In conclusion, at the price, they believe that they got a steal of a deal with it.

Customers say that getting a nodemcu starter kit and nodemcu expansion board, along with shield is useful.

Why We Like This:

This works great and it is great with open-source.
This is good for low cost, is easy to read and it is friendly.
Greatly speed up your iot application development process.
This is smart and it works for small packages.

Compatible With Raspberry Pi: Dorhea Nodemcu Shield

Buy on Amazon

The Dorhea Nodemcu Shield should be able to handle its purpose and duties with ease. The dorhea nodemcu shield is compatible with ardu ino, used for ardu ino and for programming. The Manufacturer says: We recommend using git to install the hardware package, you can always get the latest version of it. Moreover, the shield is a digital switch to control much higher voltages and currents than the esp8266 mini microcontroller, controlled by the d1, the relay will switch to allow current to flow or turn off, depending on wiring.

Lastly, the dorhea nodemcu shield allows for a great deal and it is crafted with great sales.

Overall, many buyers have used the dorhea nodemcushield for more than a few months without any complaints, and it shows no sign of giving up.

Customers found that getting a ph sensors for nodemcu, with this shield made their life much easier.

Why We Like This:

Delivers what they promise.
Good investment for the long term.

Best For Iot: Acrobotic Nodemcu Shield

Buy on Amazon

If you often find yourself scrambling for a convenient and suitable shield, Acrobotic Nodemcu Shield should be your first option for buying. The acrobotic nodemcu shield is stackable and it is good for building projects. Make sure this fits by entering your model number. The wemos d1 mini ws2812b rgb led shield is designed so that pin d2 on the wemos d1 mini v2 board is connected to the ws2812b rgb led.

Lastly, the acrobotic nodemcu shield is required for installing the header pins.

Customers also discovered that its wise to buy a ph sensors for nodemcu, along with this shield.

Why We Like This:

This is compatible with adafruit neopixel leds.
Fully addressable leds allow for individual control of color and brightness.
Ws2812b data in pin connected to pin d2.

Best For Electronic Accessories: Deeoee Nodemcu Shield

Buy on Amazon

The features department is where deeoee Nodemcu shield truly manages to shine. The Manufacturer says: We offer tens of thousands of electronic accessories and modules. Moreover, the shield is designed to be 3.3v compliant only. When it comes to searching for a reliable shield, the developed nodemcu shield is definitely your first choice.

Customers discovered that getting a nodemcu starter kit and nodemcu expansion board, with this shield made their life much easier.

Why We Like This:

Manufacturer says: We make every effort to provide customers with satisfactory service.
The goods are of good quality.
Good brand reputation.